Guide
What size air compressor for a nail gun
Nailers are rated per nail, so the answer depends on how fast you drive them.
Short answer
At a normal pace, brad and finish nailers run on any compressor, a 6 gallon pancake included. A framing nailer uses about 0.072 cu ft of air per nail, so a pancake delivering 2.6 SCFM keeps up with about 32 nails a minute and holds another 22 in its tank. For steady framing at 30 nails a minute with a margin, look for about 3.1 SCFM at 90 PSI; for two framing nailers on one hose, about 6.2.
How nailers are rated
A nail gun takes one gulp of air per nail and nothing in between, so its makers rate it in cubic feet of free air per drive (per cycle), not in CFM. SENCO explains it the same way: divide the air per cycle into a compressor's CFM and you get the nails per minute it can sustain. These are the figures in the manuals, all at 100 PSI:
- 18 ga brad nailer: 0.04 cu ft per nail (Ridgid R213BNA manual: 0.04 cu ft per cycle).
- 16 ga finish nailer: 0.045 cu ft per nail (DeWalt D51257 manual: 4.5 cu ft per 100 cycles).
- 15 ga angled finish nailer: 0.06 cu ft per nail (DeWalt D51276 manual: 6.0 cu ft per 100 cycles).
- Coil roofing nailer: 0.0415 cu ft per nail (DeWalt D51321 manual: 4.15 cu ft per 100 cycles).
- Framing nailer: 0.072 cu ft per nail (DeWalt D51823 manual: 0.072 cu ft per shot).
Other models in each class are close but not identical, and your own nailer's manual has its figure in the specifications. Paslode's sizing formula is the one to use: nailers, times nails per minute each, times air per nail, times a safety factor. Paslode uses 1.2; the calculators here use 1.3, a 30 percent margin for leaks, hose and optimistic ratings.
Compressor needed by nailing pace
| Nailer | 10 nails/min | 20 nails/min | 30 nails/min | 60 nails/min |
|---|---|---|---|---|
| 18 ga brad nailer | 0.6 | 1.1 | 1.7 | 3.4 |
| 16 ga finish nailer | 0.6 | 1.3 | 1.9 | 3.8 |
| 15 ga angled finish nailer | 0.9 | 1.7 | 2.6 | 5.1 |
| Coil roofing nailer | 0.6 | 1.2 | 1.8 | 3.5 |
| Framing nailer | 1.0 | 2.1 | 3.1 | 6.2 |
Ten nails a minute is careful trim work with measuring between nails. Sixty is one a second without a break, which a roofing or framing crew reaches in bursts but rarely holds. The compressor chart's 2.2 CFM for a framing nailer is this same arithmetic at about 31 nails a minute. Two nailers on one compressor double the figure: two framers at 30 nails a minute each need about 6.2 SCFM, a 6.4 SCFM class machine.
What the tank adds
Nailing is bursty, so the tank does real work. The air stored between cut-out and cut-in pressure drives this many nails before the motor even starts:
| Compressor | Pressure band | Air stored | Framing nails | Brad nails |
|---|---|---|---|---|
| 6 gallon pancake | 150 to 120 PSI | 1.6 cu ft | 22 | 41 |
| 20 gallon | 150 to 120 PSI | 5.5 cu ft | 75 | 136 |
| 30 gallon | 135 to 105 PSI | 8.2 cu ft | 113 | 204 |
Once the motor is running it adds its own output. A framer driving a nail a second from a pancake delivering 2.6 SCFM uses air 1.9 cu ft a minute faster than the pump makes it, so the tank lasts about 50 seconds before the pressure falls below cut-in and keeps falling. Slow to 32 nails a minute and the same pancake keeps up indefinitely. That is why a pancake is enough for a deck or a shed and a frustration for a crew. An impact wrench is the opposite case: little air averaged over a job, but breaking lug nuts loose with the trigger held drains a pancake in under a minute.
Pressure costs air
A nailer set to a higher pressure uses more air per nail. Paslode lists its F-350S framing nailer at 0.082 cu ft per nail at 90 PSI and 0.108 at 120 PSI. The absolute-pressure arithmetic the calculator uses predicts 0.105 from the first figure, so the rule holds: set the regulator to the lowest pressure that sinks the nail flush, and the same compressor drives more nails a minute.